Dock Leveler
Fixed Hydraulic Dock Leveler
Our fixed hydraulic dock leveler is essential loading‑unloading equipment for docks, warehouses and factories. Featuring flexible height adjustment, it creates a stable passage for forklifts to drive into trucks and containers. Adopting full‑hydraulic drive, it supports easy operation and positive‑negative angle adjustment to suit various vehicles. Constructed with high‑strength manganese steel beam and imported hydraulic components, it resists deformation under heavy loads for extended service life. Standard load capacities: 6T, 10T, 12T, 15T, 20T, non‑standard customization is available. It comes with anti‑slip plate, toe guard, maintenance support bar, rubber bumper and oil pump over‑pressure protection, standard spare parts enable simple maintenance and greatly improve cargo handling efficiency.
Features:
1. Operation Instructions
Run no‑load test, check fasteners and oil pipes, grease friction parts.
Lower platform level with dock, park truck.
Raise lip plate onto truck bed. Cut control power during work to prevent mis‑operation.
2. Installation Instructions
Buyer digs pit and embeds steel plates following supplier’s drawings.
Supplier provides installation and technical guidance with buyer’s cooperation.
3. Maintenance
Only trained personnel to perform maintenance.
Change hydraulic oil every 6 months (N32# winter, N46# summer).
Regularly check connections, hydraulics, electric parts and lubricate moving components.
4. Safety Notes
Do not climb or go under lifting equipment.
No overload. Keep hydraulic oil clean.
Stop and cut power for faults.
Only professionals can adjust hydraulic and electric parts; do not use defective equipment.
Dock Leveler For
SaleWorking Principle of Stationary Dock Leveler
The stationary hydraulic dock leveler is driven by an electric motor powering the hydraulic power unit to actuate the hydraulic cylinder. This lifts and lowers the main load‑bearing bridge to the required loading‑unloading height. When the height of the loading vehicle is lower than the fixed dock height, the bridge can form a negative horizontal angle to accommodate vehicles below dock height.
Manufacturing Principles
(1) The equipment shall feature advanced technology, excellent performance, reliable safety, convenient operation and reasonable cost‑effectiveness.
(2) The design, manufacturing, inspection and acceptance of the equipment shall comply with current applicable national standards and regulations.
(3) All raw materials, components and fittings shall meet national standards. Standardized parts and components are adopted for easy replacement.
(4) Bumper Block: This device effectively protects the building and dock leveler against damage. It is made of high‑tensile reinforced rubber. The outer part of the bumper block is internally fixed by embedded angle steel and bolts. The fixing bolt hole diameter is Ф18. M12 anchor bolts (outer diameter Ф16) shall be used to fasten it to the dock
Dock Leveler Operation Steps
- Hydraulic Cylinder：Heavy‑duty hydraulic cylinder ensures stable lifting & lowering performance and extended service life.
- Skirt Plates：Side protective skirt plates prevent foreign debris from entering equipment interior for enhanced operational safety.
- Lip Plate：Thickened hinged lip plate achieves stable connection with truck carriage to ensure reliable forklift crossing.
- Checkered Plate Platform：Anti‑slip and wear‑resistant checkered steel platform withstands frequent forklift rolling operations.
- Motor：High‑quality power‑unit motor features ample power output, smooth running and low failure rate.
- Electric Control Box：Integrated electric control box enables simple and convenient operation, fitted with safety warning devices.
Optional Load Capacity 6T 8T 10T 12T 14T
Platform Size Customizable 2000mm 2000mm
Equipped With Anti Slip Steel Patterned Platform Surface
Stable Lifting Safe Loading
One Key Operation
2 Pcs High Wear Resistant Bumper Blocks
Safety Skirt Safety Toe Guard On Sides Of Loading Platform
Safety Maintenance Support Prop For Deck And Lip
Shot Blasting Powder Coating And High Temperature Baking Paint For Excellent Anti Rust Performance
Robust Material Durable Safe And Reliable Quality
Dock leveler Model Reference
Check real projects we have built!
| Model | Overload(t) | Static load(t) | Platform Size(mm) | External dimensions(mm) | Power(v/kw) | Applicable forklift models | Total weight:(kg) |
| SLGD-DCQ-6A | 6 | 8 | 2000*2000 | 2000*2000*600 | 380/0.75 | 2t and below | 680kg |
| SLGD-DCQ-6B | 6 | 8 | 2000*2500 | 2000*2500*600 | 765kg | ||
| SLGD-DCQ-8A | 8 | 10 | 2000*2000 | 2000*2000*600 | 3t and below | 720kg | |
| SLGD-DCQ-8B | 8 | 10 | 2000*2500 | 2000*2500*600 | 810kg | ||
| SLGD-DCQ-8C | 8 | 10 | 2000*3000 | 3000*2000*600 | 920kg | ||
| SLGD-DCQ-10A | 10 | 12 | 2000*2000 | 2000*2000*600 | 4t and below | 780kg | |
| SLGD-DCQ-10B | 10 | 12 | 2000*2500 | 2000*2500*600 | 880kg | ||
| SLGD-DCQ-10C | 10 | 14 | 2000*3000 | 3000*2000*600 | 1020kg | ||
| SLGD-DCQ-8 | 8 | 10 | Extendable length 950 mm | 2500*2000*600 | 380v/1.5kw | 3t and below | 1200kg |
| Note:Specific dimensions are customised according to customer requirements.Please consult customer service for detailed data. | |||||||
After-Sales Service
Certificate Qualification
Customer Feedback
Starlink loading ramps are very popular in modern logistics sites. With the help of the loading ramp, the forklift can safely and quickly get in and out of the transport vehicle for loading and unloading operations.
